YW DKE TRADING COMPANY proudly recommends the SMC ITV series electro‑pneumatic proportional regulators and electronic vacuum regulators. The ITV series converts electrical signals into proportional air pressure or vacuum output, suitable for coating, pressing, clamping, vacuum pick‑and‑place and other industrial automation applications. It supports multiple fieldbuses and IO‑Link for smart integration.

Key Features
Stepless proportional control: output pressure or vacuum is proportional and stable relative to the electrical input signal, with high linearity and repeatability.
Wide range of flow and pressure options: from very low flow to high flow models.
Multiple I/O and communications: supports current/voltage inputs (4–20 mA, 0–20 mA, 0–5 V, 0–10 V), analog or switch monitor outputs, and communications including CC‑Link, DeviceNet, PROFIBUS DP, RS‑232C, IO‑Link.
High precision and fast response: typical sensitivity 0.2% F.S.; linearity typically ±1% or down to ±0.5% for high‑precision variants.
Industrial protection and reliability: enclosure equivalent to IP65; some models are grease‑free.
Modular and manifold mounting: DIN‑rail and multi‑station manifold support for compact, scalable installations.
Recommended Models
ITV0000 series (compact, small flow): ITV001m, ITV003m, ITV005m — for tight spaces and fine control.
ITV1000/2000 series (medium general purpose): ITV101m, ITV103m, ITV105m; ITV201m, ITV203m, ITV205m — support fieldbus and IO‑Link, preset inputs and digital inputs.
ITV3000 series (high flow industrial): ITV301m, ITV303m, ITV305m — for high air consumption applications.
ITV009m (compact electronic vacuum regulator): ITV009m — vacuum control from −1 to −100 kPa.
ITV209m (electronic vacuum regulator): ITV2090, ITV2091 — fieldbus and IO‑Link capable, vacuum range −1.3 to −80 kPa.
Communication/display examples: ITV10m0‑IL (IO‑Link), ITV10m0‑CC/DE/PR (fieldbus variants).
Typical Applications
Coating and electrostatic spray pressure control
Press/press‑fit force control for stamping or molding
Vacuum pick‑and‑place and handling systems
Laboratory and inspection equipment precision pressure management
Installation Checklist
Air supply: use clean, appropriate air; recommend 5 µm filtration and appropriate mist/separator as needed.
Piping and fittings: choose port size per model; leave ~1.5–2 thread turns of sealant tape exposed at end; tighten to recommended torque.
Breathing port and IP65: if IP65 equivalent needed, route the breathing port to a dry location.
Electrical wiring: wire colors typically Brown = +V, White = Signal, Blue = GND, Black = Monitor. Keep monitor/comm lines away from strong EMI. Right‑angle connectors are not rotatable; avoid applying torque.
Power and grounding: use low‑ripple DC power (24 VDC ±10% or 12–15 VDC per model); ideally give each unit its own supply to avoid ground loop issues.
Manifold mounting: order manifold parts and station count per vendor instructions; note limitations when mixing pressure ranges on a common supply/exhaust.
Maintenance and Preventive Measures
Routine checks: monthly or quarterly check air quality, filters, tubing, leaks, and wiring.
Clean piping: flush piping to remove chips/cutting oil before installation to prevent internal valve issues.
Moisture/dust handling: route breathing ports to dry locations in wet or dusty environments.
EMI mitigation: where motors/drive in the area create noise, add line filters, shielding, and proper grounding.
Consumables: solenoid valves are wear items—replace periodically under high duty cycles; contact YW DKE or SMC for spare parts.
Recalibration and parameter reset: after first power‑up or major environment changes, perform parameter re‑acquisition or initialize routine to optimize performance.
Diagnostics: bus/IO‑Link models provide diagnostics and alarm bits for quick troubleshooting via host systems.
Why Source SMC ITV from YW DKE TRADING COMPANY
Full access to genuine SMC models, technical documentation, and spare parts, with local selection, commissioning, and after‑sales support.
Support for fieldbus and IO‑Link integration for line digitization and condition monitoring.
Ability to recommend manifold, display, alarm, preset input, high‑flow or high‑precision variants to meet specific process needs.
Conclusion and Contact: For model selection, technical datasheets, quotations, or field application support, contact YW DKE TRADING COMPANY. Provide your process requirements (flow demand, set pressure range, response time, and communications needs) and we will recommend the optimal ITV model and support installation and maintenance.

Sales Manager:NENE